It has been
more than 6
months
since the last
update.Previously, updates were released more often. I would like
to
see a new
version
with a lot
of
new
chips
and
new
features.
Please add programming support for the AT89S4051 microcontroller, or show instructions so that the user can add it as a custom chip to your software for the T48 device programmer. Thank you!
There is concern that chips are read by a CH341A and not by an XGpro. Considering that their products are not cheap at all, it is a shame. They should already release more chips for the XGpro readers, otherwise their products will no longer be worth buying.
Good afternoon, I purchased your programmer XGecu T48, unfortunately it does not have some chips STC15W401AS , W55F10A , Palce 22V10H-15PC . STC15W404AS . 24LC211 . W27E512P. How can I add them to the general database?
I am using TL866II-Plus and Xgpro v12.63. Today I encountered a problem about AL008J70BF102. I Check ID ok and Read and Verify Ok but I can't Erase or Program. Please give me solution.
Why haven't they uploaded updates? There should be a method of adding memories manually, so users will help them add more memories, and they will focus their efforts on improving the product, thus increasing fame and selling more devices.
Por que no han subido actualizaciones?debería existir un método de agregar manualmente memorias, así los usuarios los ayudan a agregar más memorias, y centran sus esfuerzo en mejorar el producto, así subiría la fama y venderían más dispositivos.
Hello,
Could You please add support of Intel Strata Flash memories? I need to program 48F4000P0ZBQ0 in BGA80 case (sometimes mentioned as 88SCSP. Thanks in advance!
For a long time I have been observing the same bug in different versions of the program, which manifests itself if the program window is expanded to full screen. The bug is that from the part of the window called "IC Config Information" the ability to configure the "SPI Clock Frequency" disappears.
This bug has appeared again. Unfortunately, the software for modern programmers has become noticeably lower quality than it was in the days of the MiniPro TL866CS/A programmers...
Hi, thank you for adding the 48F4400P0VT chip in the BGA 64 case. But I can't read it using the standard BGA 64 adapter from XGECU, as it swears at some pins. Please check whether the support for this chip is configured correctly in this case? The problem is not in the chip and not in the pad, it is readable on another programmer.
p.S. It would be great if we added the ability to add chips to the user interface on our own. I don't know if it's possible. It often happens that there is a chip, but not in all cases.
This is the chip I have on an ASRock z370 Pro 4 "Winbond 25Q128JVSQ" which is also referred to as "W25Q128JVSIQ"
I already tried reading/erasing/flashing/verifying this chip with both the OTP and the non-OTP variants of the chip selected int in xGecu software.
Currently, my status Register shows only "QE" as enabled, however I don't know if it was like this originally. I may have altered/damaged the chip with my mistakes.
I have a serious problem with "Winbond 25Q128JVSQ 1849"My xGecu TL866II v12.60 gets stuck during "Erasing" in an infinite loop. It never finishes erasing.
If I try to read the chip it does show it has been erased.
If I try to program an image into the chip I always get an error during verification
Please add support for this "-SQ " variant! I cannot reflash my computer BIOS.
For a long time I have been observing the same bug in different versions of the program, which manifests itself if the program window is expanded to full screen. The bug is that from the part of the window called "IC Config Information" the ability to configure the "SPI Clock Frequency" disappears.
