Board logo

标题: New Logic Test - 74188 Vector Table [打印本页]

作者: yovish    时间: 2021-12-25 03:02     标题: New Logic Test - 74188 Vector Table

Enclosed is the new layout to be added to the logic tests.
The test was performed on the K155RE3 (256-bit, 32x8bit words PROM, open-collector outputs, analogue SN74188N) chip from IC/Microchip USSR (now Russia).


This IC is a PROM (Programmable Read Only Memory), so general testing only makes sense for a blank/clean, non-programmed chip. Because after programming, each chip can have different contents.


In the unprogrammed state, a low voltage is generated at all outputs of the 74188 microchip (74S188).

图片附件: 74188 (Blank) - Logic Vector.jpg (2021-12-25 02:59, 510.56 KB) / 下载次数 12750
http://forums.xgecu.com/attachment.php?aid=1112&k=60d78ce50a6480da3a87dcfc3b00bb13&t=1781385853&sid=cQUEeb



图片附件: 74188 (Blank) - Logic Test.jpg (2021-12-25 03:00, 327.84 KB) / 下载次数 11694
http://forums.xgecu.com/attachment.php?aid=1113&k=4c7a787a395c8726f70adc3f137c43f9&t=1781385853&sid=cQUEeb



图片附件: K155RE3 (SN74188N).jpg (2021-12-25 03:00, 589.09 KB) / 下载次数 12747
http://forums.xgecu.com/attachment.php?aid=1114&k=0b62b12559d6be4950b747948f6bc99a&t=1781385853&sid=cQUEeb



附件: TI 54-54S-74-74S Programmable Read-Only Memories.pdf (2021-12-25 03:01, 366.25 KB) / 下载次数 9031
http://forums.xgecu.com/attachment.php?aid=1115&k=80e338be7225d712460390fde329b66a&t=1781385853&sid=cQUEeb

附件: DM74S188-NationalSemiconductor.pdf (2021-12-25 03:01, 119.89 KB) / 下载次数 7413
http://forums.xgecu.com/attachment.php?aid=1116&k=4f8a78ba791896c0b2463c778d5bfa2b&t=1781385853&sid=cQUEeb

附件: 74188 (Blank).lgc (2021-12-25 03:01, 2.83 KB) / 下载次数 39236
http://forums.xgecu.com/attachment.php?aid=1117&k=18a3c1030104d935e01137b706593820&t=1781385853&sid=cQUEeb
作者: Victor87    时间: 2022-11-7 02:46

Testing for a blank/clean PROM К556РТ4 (82S126) (256x4) bits
82S126.lgc (8.06 KB)


附件: 82S126.lgc (2022-11-7 02:45, 8.06 KB) / 下载次数 37909
http://forums.xgecu.com/attachment.php?aid=1541&k=58e035ddeb85df3f6bddff473cf1a64c&t=1781385853&sid=cQUEeb




欢迎光临 XGecu Programmer Forums (http://forums.xgecu.com/) Powered by Discuz! 7.2