返回列表 发帖

microwire eeprom (AT59C11, OKI 16911G, GI5911 and compatibles)

I need to program some OKI16911G/compatibles chips. They are similar to 93c46 but different opcodes so I think this should be easy to implement.

https://pdf1.alldatasheet.com/da ... 8/OKI/MSM16911.html
https://pdf1.alldatasheet.com/da ... /ATMEL/AT59C11.html

Thanks!

Regards,
William

Bump, any update on this?

TOP

回复 2# wLLm


   Please wait, mark it,  will be added in the future

TOP

I see that OKI 16911G and compatibles has been added for T56. Will this be added too for the TL866II plus?

TOP

回复  wLLm


   Please wait, mark it,  will be added in the future
admin 发表于 2021-5-28 10:22


I bought the T56 to program the OKI16911G but writing doesn't work, if I write 0xFD during verify it reads 0xFF.  I tried a TS59C11 which is OKI16911/AT59C11 compatible but with the same result. I'm using Xgpro v11.10.
  1. **************************************************************

  2. APP Version : 11.10   Model : T56

  3.      Device : OKI16911(8b)  @DIP8

  4. **************************************************************



  5. Pins Detected Passed!

  6. Erase  ...Succeeded. Time : 0.015 S

  7. Programming FLASH ...Succeeded. Time : 31ms

  8. Verifing FLASH ...

  9. ERROR!   CODE Address:0x000000    Buf_Val:0xFD    IC_Val:0xFF

  10. Programming  ...Failed
复制代码

TOP

回复 5# wLLm
I view the data sheet  of TS59C11 /OKI MSM16911/AT59C11 . they are all the same.

I tested no problem
OKI59C11.png

TOP

回复  wLLm
I view the data sheet  of TS59C11 /OKI MSM16911/AT59C11 . they are all the same.

I t ...
admin 发表于 2021-7-22 09:12


Thanks for the reply, indeed, I should be able to program the chips with T56. What could be the issue that I cannot write the chips? The chips I have are new oldstock OKI 16911G and TS59C11.

update:
I was able to write an Atmel AT59C11. But the original 16911's that I have won't write the same goes for TS59C11. The OKI and TS are quite a bit older than the Atmel one. Eventough the chips are the same, could it be that there is some timing issue perhaps? Which chip did you test exactly?
If I read the datasheets correctly, Atmel's chip is from 1998, TS is from 1988. For the 16911 I could not find a date reference in the datasheets but I expect this could be late 1980s or early 1990s.
One difference that I could find is the max Clock Frequency. for AT59C11 that's 1MHz and for ST59C11 and MSM16911 that's 250KHz. There are also slight differences in the opcodes, it seems that AT59C11 is a bit more flexible than it's compatible counterparts.

TOP

回复 7# wLLm

T56 Frequency  Clock is 250KHz. and opcodes is right.
Please wait, I will buy OKI MSM16911 to test.

TOP

回复 7# wLLm

The reason has been found and we will be fixed in the next upgrade.

TOP

回复  wLLm

The reason has been found and we will be fixed in the next upgrade.
admin 发表于 2021-7-26 11:55



I'm looking forward to the upgrade! Is it included in the 11.11 version? Just out of curiosity, what was the issue?

TOP

回复  wLLm

The reason has been found and we will be fixed in the next upgrade.
admin 发表于 2021-7-26 11:55



Thanks a lot! it works I can finally program the 16911G! Great service and a great product :)

TOP

返回列表 回复 发帖